Type |
Select the Type as Record to configure a GV I/O
recorder channel. |
Timecode Mode |
The timecode mode for the channel can be set at Fixed
Format or Time of Day. |
Input |
Input signal type that has been connected to the channel at the GV I/O Live Ingest and Playout Server. Available input signals are in the list below:
- Unassigned - The channel input is set to this
initial setting by default. No other settings are configurable when this
option is selected.
Note: Changing a channel's I/O configuration to Unassigned will set
channel configuration information to a default state and release any
SabreTooth licenses associated with the channel.
- SDI - Configures the channel to use SDI input.
Requires the GVIO-HW-CORVID88 hardware configuration and GVIO-SVR-SDI
license per channel.
- SMPTE 2110 - Configures the channel to use
10/25GigE SFP input and allows for SDP file import. Requires the
GVIO-HW-CX5 hardware configuration and GVIO-SVR-IP license per channel.
- SMPTE 2022-6 - Configures the channel to use
10/25GigE SFP input and allows for a single RTP URL entry of the form
rtp://ip_address:port_number as
described below.
- ip_address : The multicast IP address of the
SMPTE 2022-6 media stream to be recorded
- port_number : The UDP port configured for the
media stream
For example, “rtp://239.100.100.1:10000”.
Requires the
GVIO-HW-CX5 hardware configuration and GVIO-SVR-IP license per
channel.
- Web Stream - Configures the channel to use 10GigE
RJ45 input and allows for a single RTP URL entry of the form
rtp://ip_address:port_number as
described below.
- ip_address : The multicast IP address of the
media stream to be recorded
- port_number : The UDP port configured for the
media stream
For example, “rtp://239.100.100.1:10000”.
Requires the
GVIO-HW-CX5 hardware configuration and GVIO-SVR-WEB license per
channel.
|
Label |
The label that you want to assign to the GV I/O channel. |
Receiving Interface |
For a channel configured for SMPTE 2110 or SMPTE 2022-6 input signal
type, enter the IP address that goes with the SFP connector used to receive
the media stream. |
2022-7 Redundancy |
Select to enable or disable redundancy of ingests. This is only
applicable when SMPTE 2110 is selected for the channel Input. |
2022-7 Receiving Interface |
When the 2022-7 redundancy option is enabled, a 2022-7 Receiving
Interface (IP address) is also required, and it represents the IP address of a
second GV I/O input as the backup. |
Channel Format |
Select a format for the channel
from the drop-down list. The setting determines the video format expected at
the GV I/O channel’s input. |
Video Compression Format |
Select a format for the channel from the drop-down list. This setting
also determines the video codec used to compress the video while recording.
|
Dynamic Range Type |
Select a dynamic range type for the channel from the drop-down list. The
default is set to SDR, as this is the only available
option if you selected SDI, SMPTE 2022-6, or Web Stream for the channel's
input. If you selected SMPTE 2110 for the channel's input and already
installed the GVIO-SW-OPT-HDR license, you can select either
HLG or PQ dynamic range type
for the HDR work flow.
Note: HLG or PQ option can only be selected if the channel format is set to
1080p or 2160p.
|
Data Rate |
Select a data rate for the channel. |